SECTION I - GENERAL INFORMATION
MANUFACTURER: Inland Vacuum Industries, 35 Howard Avenue, Churchville, NY 14428
DATE PREPARED: 1/19/93
PRODUCT CODE: 404700
PRODUCT NAME: Inland TW
NPFA RATING:
Flammability: 1 Health Hazard: 0 Reactivity: 0 Special Hazard: NONE
CAS NUMBER: 8042-47-5
CHEMICAL FORMULA: (CH2)n 20 =< n =< 40
GENERIC NAME: Solvent refined technical white petroleum oil
TRADE NAMES AND SYNONYMS: Alcatel300, Edwards TW, Leybold HE-400
SECTION II - REGULATED INGREDIENTS
(29 CFR 1910. 1200)
REGULATED MATERIALS AT CONCENTRATION OF 1% (WT) OR GREATER
NO HAZARDOUS INGREDIENTS. MATERIAL IS 100% TECHNICAL WHITE PETROLEUM OIL. MATERIAL HAS BEEN SUBJECT TO SEVERE SOLVENT REFINING.
SECTION III - HEALTH HAZARD DATA
POSSIBLE ENTRY ROUTES: Ingestion, Inhalation of oil mists
TARGET ORGANS: None Known
EFFECTS OF OVEREXPOSURE:
ACUTE EFFECTS: Exposure to oils mists may cause nausea and eye irritation. Detailed studies have not been made, but material is not expected to be dermatitic or a sensitizer.
CHRONIC EFFECTS: None known.
FIRST AID PROCEDURES: Skin - wash with soap and water. Eyes - flush with water. Contact a physician! Ingestion -give liquids and induce vomiting if victim is conscious. Contact a physician! Small amounts in mouth may be washed out.
SECTION IV - FIRE AND EXPLOSION HAZARD
FLASH POINT: > 213 degrees C METHOD USED: Cleveland Open Cup EXPLOSIVE LIMITS: LOWER: Unknown UPPER: Unknown
EXTINGUISHING MEDIA: Water fog, chemical foam or carbon dioxide.
SPECIAL FIREFIGHTING PROCEDURES: Wear breathing gear when fighting fires in enclosed spaces; incomplete combustion of this material produces carbon monoxide!
UNUSUAL FIRE AND/OR EXPLOSION HAZARDS: None.
SECTION V -PHYSICAL PROPERTIES
PHYSICAL STATE: Liquid VAPOR PRESSURE: < .001 Torr @ 25 degrees C BOILING POINT: 158 degrees C EVAPORATION RATE(ether = 1): Nil VAPOR DENSITY: Approximately 14 WT % VOLATILES: Nil SPECIFIC GRAVITY: 0.86 VISCOSITY: 56 cst @ 40 degrees C SOLUBILITY IN WATER: Nil APPEARANCE: Transparent, colorless, viscous liquid with faint petroleum odor.
SECTION VI - REACTIVITY DATA
STABILITY: Material is stable
CONDITIONS TO AVOID: Continuous exposure to temperatures > 200 degrees C
INCOMPATIBILITY (MATERIALS TO AVOID): Strong Oxidizers
HAZARDOUS DECOMPOSITION PRODUCTS: Incomplete combustion may produce carbon monoxide.
SECTION VII - RELEASE PROCEDURES
PROCEDURE TO BE FOLLOWED IN EVENT OF RELEASE: Small spills may be wiped up with a rag. Large spills should be picked up immediately with an absorbent.
PROCEDURES FOR PROPER WASTE DISPOSAL: Proper waste disposal procedures are dependent on the product's end-use. Check applicable Federal, State and Local covering treatment, storage and disposal of your process effluents.
SECTION VIII - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: See notes on ventilation below.
PROTECTIVE GLOVES: Yes - made of oil-impermeable rubber.
SAFETY GLASSES/GOGGLES: Yes - glasses should have side shields.
OTHER PROTECTIVE EQUIPMENT: None should be required under normal use.
VENTILATION: US Gov't 8 hr TWA limit for exposure to oil mists is 5 mg per cubic meter.
LOCAL EXHAUST: As required to meet limit shown above.
MECHANICAL EXHAUST: As required to meet limit shown above.
OTHER REQUIREMENTS:
SECTION IX - SPECIAL PRECAUTIONS
SPECIAL HANDLING PRECAUTIONS: None
SPECIAL STORAGE PRECAUTIONS: None
ADDITIONAL INFORMATION: NFPA Class III B material